Quiet Super Steam Generator

Out of stock
SKU
24450
Price £199.99

It’s time to go full steam ahead – without all the noise. Quiet yet powerful, this is a dream of a steam generator. With 7 Bar Pressure, 290g Steam Output and at 2400W, you have plenty of power to blast through the toughest of creases. Whilst the Quiet Technology, lets you enjoy up to 10% Quieter ironing*, so that you can hear your favourite TV programme!

*Vs Previous model

Price £199.99

Documents & Support

User Manuals

User Manual

Product Registration & Warranty


Register your Product

Register your product to benefit from an extended warranty on top of our standard manufacturer warranty as well as access to exclusive content.


Warranty Information

We will repair or replace products that are defective within the warranty period where the product is used and maintained in accordance with the instructions. Spare parts for this product are covered by a one year guarantee. Your statutory rights are not affected.

Reviews

Write Your Own Review
Write a Review:Quiet Super Steam Generator
Select Rating

FAQs (14)

Customer Questions
Dirty water and impurities come out of the soleplate during ironing, what should I do?

Self clean is required or has not been carried out correctly - Refer to the instruction booklet for self clean instructions.

Descaling required (if not a self clean iron) - Descale using a suitable descaler for plastic parts and follow instructions on the packet.

The iron may also require new filter cartridges.

Is it necessary to empty the water tank after each use?

Yes, we recommend you always empty the water tank after use and store the iron in an upright position to avoid corrosion and damage to the soleplate.

The steam generator does not produce any steam. What can I do?

There is an airlock in the unit - Prime the unit by putting the generator unit on the floor and hold the iron itself up higher. Make sure that you have the heat and steam settings on 'maximum' then keep your finger on the trigger for about 5 – 6 minutes without letting go and try shaking the wire. This will not damage the unit and we only advise our customers to do this if they have an air lock.

Whilst carrying out the above you will hear the usual pulsating noise as normal, which should go quieter as the shot of steam works its way through the unit.

You can also try to prime the unit the opposite way round by having the generator unit on a high surface holding the iron at a lower level.

Why does the steam output get weaker?. What should I do?

It is common for the Steam generator to experience dip in steam pressure/ output when the water is being pumped from water tank to the boiler. This dip is momentarily and it restores to normal rate.

It is also common for the initial burst of steam to be higher and it tapers off to a steady level with continuous triggering of the steam trigger.

This is due to the initial release of build up pressure inside the boiler and this pressure will drop to a steady state level when the steam trigger is continuously depressed. It builds up pressure again when the trigger is released.

If steam output does not recover, kindly check steam generator panel for any notifications and take remedial action. e.g. water tank empty light or steam generator gone into standby mode.

What type of water should I use?

Your appliance has been designed to be used with tap water.

In case you live in an area with very hard water, fast scale build-up may occur. Therefore, it is recommended to mix 50% distilled water and 50% tap water, or to use only distilled water to prolong the lifetime of your appliance.

Do not put perfume, vinegar, starch, descaling agents, ironing aids or other chemicals in the water tank, as your appliance is not designed to work with these chemicals.

The water at home goes through a softener, will this have any affect inside the machine?

There are different types of water softener, if it is a filter it is OK.

If it is adding chemicals or additives into the water, it may damage the Steam Generator and give a poor steam performance.

Why does the steam generator switch off by itself.

Some of our irons have an auto-off function which is activated automatically when the steam generator has not been used for around 15 minutes.

Press the power on/off button to switch on the steam generator again.

How to fill/refill water when tank is empty?

The water tank is detachable. Detach it, and fill the water tank under the tap. You may fill the water tank any time during ironing.

How to avoid the iron leaving shine/ print on my garment during ironing?

The likely cause for this is that the garment surface being ironed is uneven; such as pocket or fold line below the garment.

To prevent shine/print, avoid ironing over uneven surface or use a piece of cotton over the surface during ironing.

What causes the noise in the steam generator when I press the steam trigger? Is this noise normal?

This noise is caused by movement of the valve that lets steam pass from the steam generator to the iron each time when the steam trigger is pressed. This sound is normal.

I hear noise coming out of the steam generator during ironing. Is this normal?

It is normal to hear occasional pumping sounds coming out of the steam generator when water is pumped from the water tank into the steam generator.

Water droplets appear on the garment during ironing

The water droplets may appear on the garments when you have steam ironed for a while. This happens because steam has condensed on the ironing board.

Dry the wet spots on the garment and the ironing board cover by passing the iron over them without pressing the steam trigger. If the underside of the ironing board is wet, wipe it dry.

Make sure you use a mesh-top ironing board with a thick felt material. This minimise steam condensation on the ironing board.

When possible, select a lower steam setting or use less steam during ironing.

Use steam ironing during the first few strokes of the iron across the garment, then release the steam trigger and finish up with dry-ironing strokes.

Replace the ironing board cover if the sponge material has worn out. You can also put an extra layer of felt between the ironing board and the ironing board cover to minimise condensation on the ironing board.

Water droplets come out of the soleplate during ironing, what should I do?

The droplets are caused by steam that was still present in the hose which has cooled down and condensed into water. This causes water droplets to come out of the soleplate.

To reduce this occurrence, it is recommended Steam away from the garment for a few seconds first.

How to clear an airlock on a steam generator iron?

Prime the unit by putting the generator unit on the floor and hold the iron itself up higher. Make sure that you have the heat and steam settings on 'maximum' then keep your finger on the trigger for about 5 – 6 minutes without letting go and try shaking the wire. This will not damage the unit and we only advise our customers to do this if they have an air lock.

Whilst carrying out the above you will hear the usual pulsating noise as normal, which should go quieter as the shot of steam works its way through the unit.

You can also try to prime the unit the opposite way round by having the generator unit on a high surface holding the iron at a lower level.

Please, mind that only logged in users can submit questions