Help Center

No, the kettle is intended for heating water only. Do not use it to heat up any other liquids

The water in this kettle is heated up rapidly, which causes the noise. This is a normal phenomenon and there is nothing wrong with your kettle.

Clean the outside of the kettle and the base with a warm damp soft cloth. Do not let the moist cloth come into contact with the cord, the plug and the connector of the base. Never immerse the kettle or its base in water and do not use abrasive cleaning...

Depending on the hardness of the water where you live, small spots may appear on the heating element of your kettle when you use it. This is the result of scale build-up on the heating element and on the inside of the kettle over time. The harder the...

While the kettle will still function without the anti-scale filter, the flow of the pour may not be as smooth and there may even be a little ‘spitting’ during the boil with a full kettle. And of course, the function of filtering out minerals from getting...

Yes, you have to descale your kettle regularly. Minerals present in tap water will cause scale to build up inside your kettle when water is heated. Regularly descaling your kettle will help to: reduce the boiling time and save energy, keep the inside...

This problem may have multiple causes: The appliance is not connected to the mains.
The dry-boil protection has been activated.
The kettle needs to be descaled.
Below you can find the solutions for each of these causes. Solution Cause 1: The...

This indicates that the kettle has been filled beyond the maximum level indication. For safety reasons, you should never fill the kettle beyond the MAX indication on your water level indication window.

If you find some condensation or a few drops of water on the base, this is not a manufacturing defect but a normal occurrence. However, if you see more water than just a few drops on the base or under the base, please contact the Russell Hobbs Consumer...

Try descaling the kettle according to the descale procedure. Rinse carefully afterwards. If this does not help, please contact the Russell Hobbs Consumer Service Department on 0345 658 9700.

This can be due to type, thickness or freshness of bread - uneven cut bread will not toast evenly. Also try using different bread type.

On 4-slice models around 95% of the outer elements will glow red after a number of uses but the inner elements will not as they only have half the power of the outer ones.

Yes you can, just press the cancel button.

Yes you can toast bagels (some of our toaster have bagel feature) and other bread types).

Before cleaning make sure you have unplugged your toaster and let it cool down. Then slide out the crumb tray clean it and then replace and try to do this regularly. Wipe the outside of the toaster with a damp cloth, and then dry.

It is better to use slices of bread. Dry/stale bread toasts more quickly than fresh bread and thinly sliced bread toasts more quickly than thickly sliced bread.

The toasting time is automatically altered to give you the same degree of browning as you would get with unfrozen bread toasted on the same setting.

It is a tray at the bottom of the toaster that collects the loose crumbs - This tray should be regularly removed and cleaned.

The browning control allows you to choose how much you want your bread toasted.

Before cleaning make sure you have unplugged your toaster and let it cool down. Then slide out the crumb tray clean it and then replace and try to do this regularly. Wipe the outside of the toaster with a damp cloth, and then dry.

No, hand it in at an official collection point for recycling. to help preserve the environment. You can also return it to us and we will recyle it for you. Our addresses for recycling are WEEE Recycling Department, Russell Hobbs Ltd, Heathmill Road, ...

Clean the outside of the coffeemaker with a soft cloth moistened with warm water. Filters, filter holders and carafes can be cleaned in warm soapy water, rinsing thoroughly afterwards to remove all traces of soap. Do not immerse the coffeemaker or its...

You may have connected too many appliances to the same circuit. Unplug a number of other appliances connected to the same circuit and then plug the coffee maker in again. If the fuse continues to blow, please contact the Russell Hobbs Customer Service...

If the taste of your coffee is not good from the start, please keep in mind that: You should at least brew the minimum amount of coffee as indicated on the jug and water container.
The brand of coffee can influence the taste.
You might want to...

The amount of ground coffee put in the filter influences the coffee strength. In general, 1 level coffee spoon is enough for 1 small cup of coffee. Depending on your strength preference, you can use less ground coffee for a milder taste and more ground...

If you have used the coffeemaker for quite some time and the temperature of the coffee decreases, we advise you to descale the coffeemaker.

Yes. Descaling is an important part of the maintenance of your appliance. You should descale your appliance regularly - at least monthly. To descale your appliance, you can use any descale agent suitable for use in plastic bodied products or use white...

Some dripping is normal and is caused by condensation of steam, so there is no need to worry.

The appliance generates steam during the brewing cycle. Therefore a small amount of condensation on the lid of the coffee maker is normal and does not cause problems.

If the coffeemaker is not working after you have switched it on, please check if the plug of the coffeemaker is properly inserted in the wall socket and if the wall socket is working. If this solution does not solve your problem please contact the Russell...

Yes, still mineral water is fine but do not use sparkling water.

Please check the following: The coffee you are using may be ground too fine. This stops the water from passing through.
Only use coffee recommended for espresso machines.
You may have pressed the coffee too hard in the filter.
If this solution...

Yes. Descaling is an important part of the maintenance of your appliance. You should descale your appliance regularly - at least monthly. To descale your appliance, you can use any descale agent suitable for use in plastic bodied products or use white...

Answer 1: The steam control may have been set to the no steam position. Set the steam control to a steam position. Answer 2: There is no water in the tank and/or the settings are not set correctly. Solution: Step 1: Ensure there is water in the tank...

Step 1: Check that the connection to the plug is secure and not loose and also check how many appliances are using the same output. Failure could be caused by over current in your mains. Step 2: Check the iron's power cord for visible signs of damage...

Answer 1: The (vertical) steam boost function has been used too often within a very short period. Put the iron in a horizontal position and wait for a while before using the (vertical) steam boost function again. Answer 2: The iron is not hot enough...

Make sure there is enough water in the tank and check that the spray button is able to spring back on its own after pressing. If the spray nozzle hole is blocked, you can clean it carefully with a sharp needle or pin.

Make sure the iron is plugged into a working mains power and set the temperature dial to a desired position. It is normal for the orange pilot light to turn on and off during ironing. It comes on as the iron is heating up, and goes off when it is hot...

Some parts of the appliance have been slightly greased and as a result, the appliance may produce some smoke when it is switched on for the first time. Also, if there is remaining water in the soleplate from the last usage, the smoke observed may actually...

Your iron has multiple thin layers of coating and light scratches will not impede the performance of the iron. You can continue using the iron as per normal.

Fabrics can acquire shiny patches if they are ironed at too high temperatures. Try a lower temperature setting. Also, to prevent shiny patches, you can put a cloth (e.g. a tea towel) between the iron and the fabric.

Your appliance has been designed to be used with tap water.

There may be several reasons for this: Your iron produces a lot of steam. Steam could have condensed on the ironing board cover, making it wet and cause water marks on your garment when the iron is pressed on it.
Ironing aids or fragrance water could...

Self clean is required or has not been carried out correctly - Refer to the instruction booklet for self clean instructions. Descaling required (if not a self clean iron) - Descale using a suitable descaler for plastic parts and follow instructions ...

Yes, we recommend you always empty the water tank after use and store the iron in an upright position to avoid corrosion and damage to the soleplate.

There is an airlock in the unit - Prime the unit by putting the generator unit on the floor and hold the iron itself up higher. Make sure that you have the heat and steam settings on 'maximum' then keep your finger on the trigger for about 5 – 6 minutes...

It is common for the Steam generator to experience dip in steam pressure/ output when the water is being pumped from water tank to the boiler. This dip is momentarily and it restores to normal rate. It is also common for the initial burst of steam to...

Your appliance has been designed to be used with tap water. In case you live in an area with very hard water, fast scale build-up may occur. Therefore, it is recommended to mix 50% distilled water and 50% tap water, or to use only distilled water to...

There are different types of water softener, if it is a filter it is OK. If it is adding chemicals or additives into the water, it may damage the Steam Generator and give a poor steam performance.

Some of our irons have an auto-off function which is activated automatically when the steam generator has not been used for around 15 minutes. Press the power on/off button to switch on the steam generator again.

The water tank is detachable. Detach it, and fill the water tank under the tap. You may fill the water tank any time during ironing.

The likely cause for this is that the garment surface being ironed is uneven; such as pocket or fold line below the garment. To prevent shine/print, avoid ironing over uneven surface or use a piece of cotton over the surface during ironing.

This noise is caused by movement of the valve that lets steam pass from the steam generator to the iron each time when the steam trigger is pressed. This sound is normal.

To maintain your vacuum machine we recommend that you wash your filter(s) at least once every 3 months and replace once a year.

If you have allergies or asthma, you need a vacuum cleaner with a HEPA (High Efficiency Particulate Air) filter so that when you vacuum, you will actually trap microscopic allergens instead of simply stirring them up and polluting the air. HEPA filters...

In general, canister vacuum cleaners are more versatile, lighter, and easier to maneuver. Canister vacuum cleaners also provide smoother transitions between different types of flooring. Upright vacuums are best suited for homes with carpet in every ...

The simple answer is "Yes". Vacuum cleaners with dust bags are generally healthier for allergy sufferers because the bag keeps the dust out of the air. However, not all bags are created equally. Some bags have large pores which allow allergens to escape...

Not necessarily. The amperage of a vacuum cleaner's motor measures electrical current, not performance or suction power. The performance of the vacuum cleaner depends on the overall design, the filtration, and the air flow.

A turbobrush is air-driven, while a powerbrush is driven by electricity (usually an independent motor in the brush attachment itself).

Generally, you should use as many as seven strokes for high-traffic areas; three or four for lighter ones.

When you're vacuuming pile carpets and rugs, you should use the turbo brush, but when you're cleaning bare floors and walls, it's best to use the wall/floor brush. To get dust out of drawers, heating and air-conditioning vents, and from under larger...

If the filter shows signs of wear, or is excessively dirty or torn, it's time to replace it. HEPA filters - ones that remove most dirt particles - should be changed after six months. The owner's manual will tell you where the filter is located.

It is very common for a new appliance to give off an unpleasant smell or emit some smoke the first few times it is used. This phenomenon will stop after you have used the appliance a number of times. The appliance may also give off an unpleasant smell...

The quantity you put in the jar was too large. When processing foaming ingredients, do not fill the jar beyond two thirds of its overall capacity.

During processing, you can remove the cap to add liquid and solid ingredients. Switch the blender off before adding solid ingredients.

Check if the lid is closed properly.
Never open the lid during processing.
To prevent spillage, do not overfill the blender (please refer to the instruction booklet).
When you have switched the appliance off, wait until the blade has stopped...

Loosen the ingredients with a spatula (switch the appliance off before doing so) or by adding some liquid.

Loosen the ingredients with a spatula (switch the appliance off before doing so).

It depends on the quantity and the ingredients, however, on average the time for blending is about 30 - 60 seconds.

No, to avoid damage to the jar let the liquid cool down to the sort of temperature you can comfortably handle, i.e. liquid temperature below 40°C.

You can use the blender jar for: Blending fluids, e.g. dairy products, sauces, fruit juices, soups, mixed drinks, shakes.
Mixing soft ingredients, e.g. pancake batter or mayonnaise.
Pureeing cooked ingredients, e.g. for making baby food.
Crushing...

When you turn the control knob to the pulse setting, the appliance runs at its highest speed as long as you keep the knob in this position. Use the pulse setting if you want to have more control over the processing jobs.

You can use the whisk to whip egg whites, cream, sponge cake mixtures and soft desserts.
Note: Do not use the whisk to prepare a plain cake mixture with butter or margarine.

Let the ingredients cool down to approximately 40°C before processing them.

Cut the ingredients into approximately 2 x 2 x 2 cm pieces.

It depends on the ingredient, however, in general it can be said, the harder the ingredients the less you should process at once, on average with a half filled beaker you would receive a good result.

You can use the chopper to chop herbs, onions, nuts, Parmesan cheese, etc. You can also use the chopper to prepare dips and pastes like pesto, guacamole, salsa, tapenade, etc.

No, just use warm water with washing-up liquid to clean them. Do not use abrasive or corrosive cleaning agents or scouring pads.

Yes, if you process very hard ingredients such as bones and fruit with stones.
You can process ingredients like parmesan or chocolate etc.